GOOD FOOD… GOOD FEELINGS

 

DELICIOUS FOOD. TO FIT YOUR LIFESTYLE.

 

LIFE IS TOO SHORT FOR AVERAGE FOOD!

 

in Home improvement tips
Created: 13 January 2016

kitchen_designRenovating your personal kitchen? Here are a few handy strategies for kitchen remodeling.
You can save a complete lot of money on your own remodel by installing your kitchen cabinets yourself. Allow the required time for the working job done and obtain some friends to greatly help.
Strategies for Hanging Cabinets:
- Remove all cabinet doorways and drawers to create them better to install and to prevent damaging them during set up.
- You may need a pencil, tape level and measure to mark the precise position of the cupboards on the walls.
- It is better to install top of the cabinets first, starting within the corner(s).
- To install upper cupboards, determine their location with regards to the bottom cabinets. Add the elevation of the bottom cabinet to the thickness of one's countertop (base cupboards are usually 34-1/2 high and countertops are often 1-1/2 ins thick.) Adding 18 ins for the area in between top of the and lower cupboards. Your total ought to be about 54 ins. That's where the bottom of top of the cabinet will sit.
If the ground isn't level, discover the highest point across the wall where in fact the cabinets shall be installed. Tag a chalk line over the wall after that attach a 2x4 ledger in to the wall studs to greatly help support the cupboards while installing.
- Slice holes for the drinking water lines on the relative back of the cabinet.
If cutouts are essential for electrical boxes, trace the package with lipstick contain the cabinet in the right place and push firmly then. The lipstick shall transfer to the cabinet. Connect the relative lines, drill a pilot hole and create the cut-out with a jig noticed.
- Be sure you fasten the cupboards to wall studs. In case a cabinet hits only 1 stud, work with a toggle bolt to keep it secure.
- When hanging cabinets, check for plumb and levelness frequently. Don't completely tighten the screws before cabinets are usually plumb, flush and degree. Use shims to greatly help achieve evenness.
- Use clamps to carry together cupboards while securing to walls.
Finding Bargains:
- When searching for appliances, search for floor versions. You're usually only quitting the box that came in. Make sure to talk with the dealer concerning the warranty. They could be ready to extend the guarantee to unload that.
- Shop within early fall for home appliances. Last year's models have to go to make space for another year's models.
- Shop scratch-and-dent appliance product sales. Make certain the scratches are aesthetic and not structural.
- Require volume discounts, some accepted places make discounts available if you buy all of your appliances in a single place.
- When searching for windows and doors, don't just examine the big package retailers, go to your neighborhood building provider, (where your contractor stores). The savings can be to 20 percent up.
- Look for cabinet merchants or wholesalers offering free design solutions such as for example measuring your kitchen area and planning your design.
- Go to the place that offers granite slabs directly. It is possible to save 25 to 30 % by trimming out the center man.

in Home improvement tips
Created: 01 December 2015

Fence Basics
Wood fences will be the most common kind of affordable, high quality fencing we build, due to wood's availability, it is aesthetic versatility, and its own relative low cost of maintenance and building. While it can be done to purchase prefabricated solid wood fence panels, stick developing your fence offers even more flexibility, greater handle over the standard of materials you utilize, and, often, a far more pleasing fence aesthetically.
FenceThe most typical species useful for stick-built wood fences include pine, spruce, fir, cypress, red cedar, white cedar, and redwood. When choosing the wood that may constitute your fence it really is better use heartwood instead of sapwood. Heartwood, that is an older solid wood taken from the within of a tree, will routinely have less knots and won't decay as rapidly as sapwood, that is a younger solid wood taken from the exterior of a tree. The solid wood materials that define a fence consist of pickets, rails, and posts.
·Pickets will be the vertical boards that define the finished surface area of a fence. They're typically 1/2" - 1" thick, by 4" - 6" wide.
·Rails will be the horizontal users to that your pickets are fastened. They're commonly 2" solid by 3" - 4" broad.
·Posts, which are usually buried underground partially, will be the vertical structural users that assistance the rails and pickets of a fence. They're typically 4" - 6" solid by 4" - 6" broad.
Stick building the opportunity is offered by a wood fence to be creative; however, it must be noted that many traditional varieties of fence are nicely received by neighbors.
·Picket fences will usually have two rails, with spaced pickets using one part of the fence equally. They range high from 3' to 4'.
·Shadowbox fences could have three rails, with equally spaced pickets on two sides of the fence. Shadowbox fences include a picket on one part positioned alternately to a picket on the opposing part. They're typically 6' tall.
·Board up to speed fences (see picture above) have several rails, based on the elevation of the fence. Pickets are butted firmly together on one part of the fence. They typically range high from 3' to 6'.
Creative touches could be added to conventional fences, such as ornamental Gothic pickets, curved picket tops, and/or ornamental post caps. This info will add flair from what would be a flat-topped wood fence otherwise.
Prior to creating a fence on your own property, you should have a precise knowing of where your premises lines are situated. You will have to contact your neighborhood utility companies to tag the positioning of any underground utility mains which may be situated on your premises. Make sure to obtain any necessary developing permits, check with your local zoning needs, historic district guidelines, and/or town association regulations regarding fences on your own property. You may even deliver a very hot bowl of cookies or provide over an ice-cold 6-pack to your neighbor's home prior to increasing a fence. This can give you the possibility to have a discussion with your neighbor relating to your intentions, instead of surprising them together with your new fence.
Layout
It is advisable to develop a plan on papers, prior to creating a fence. This will provide you with the possibility to make the modifications necessary to make sure that the finished look of the fence is really as expected and it'll allow you to precisely estimate just how much material you need.
After the fence has been planned by you in writing, it is possible to locate the corners and the finishes of the fence on your own property. The corners, finish, and fence line ought to be set back again from your property collection as described by your neighborhood jurisdiction.
Accurately place a wood stake to mark the biggest market of almost all end and corner posts.
Drive a nail in to the middle of the solid wood stake and operate a type of string tautly from stake to stake. Fence posts are generally apart spaced 6' to 8'. Starting at one part or an end, gauge the appropriate distance to another post. Define the biggest market of this article and mark the positioning with a solid wood stake. Keep on with this until all posts have already been staked and located.
Setting the Posts
Once all the post locations have already been located and staked you're prepared to set posts. Depending on the dimension and complexity of one's fence, the posts could be set in among three ways.
Soil-packed post: Place 6" of gravel in underneath of the post hole and pack the area round the post with soil.
Post occur concrete: Location 6" of gravel inside underneath of the hole and fill up the remaining space round the post with cement. Tubular concrete forms may be used with this particular method, if desired.
Post anchored to cement pier: A cement pier is formed inside the bottom with a metal article anchor embedded inside it. Tubular concrete types can be used with this particular method, if desired.
For the intended purpose of this short article we'll assume you're setting posts which are rated for ground contact and in a position to be cast in concrete. Post holes ought to be dug with an article hole digger or an auger to a depth of 1/3 to 1/2 of the finished post elevation above ground and 3 x the width of the article. For example, if your post shall be 6' high above finished grade and you are employing 4" x 4" articles, you need to dig to an approximate depth of 36" and a width of 12". If your fence will undoubtedly be taller with larger articles, adjust these measurements appropriately.
Place and compact a new 6" foundation of gravel inside each article hole and, if desired, place a tubular cement form in the hole.
Insert the post in the heart of the hole and brace the article by anchoring to the bottom, two 2 x 4s, one on each part of the post.
Ensure that the post is with a level plumb. Do this for every post location, after that tautly run string near the top of each post and close to the bottom part between each article. The string at the very top should be utilized to regulate the height of every post, to ensure they're aligned properly. The string across the bottom ought to be used to check on the alignment at the facial skin of each post. Any necessary adjustments ought to be made at the moment by repositioning the article within the hole.
Once the articles are plumb, aligned, and properly located it is possible to pour concrete. Quick Tip: Unless you want to observe concrete, terminate the pour before achieving grade, leaving several inches between quality and the very best of the pour. This can enable you to fill the rest of the area with soil. If you love to let drinking water slope from the article, overfill the hole with concrete. Work with a trowel to form a slope at first glance of the cement above grade. Time ought to be permitted for the concrete to cure ahead of attaching the fence rails. Depending on the kind of concrete you decide to make use of and the outside ambient temperature, you might need to wait 1-3 times before attaching the rails.

in Home improvement tips
Created: 10 August 2012
kitchen remodeling columbus ohio - kitchen

Sometimes your home needs a little pick-me-up, and a great place to get started is in the room that is very likely the "heart" of your home with a kitchen remodeling.

Whether you're looking to improve your kitchen's appearance or its functionality, the right remodel can help you get exactly what you need. Your kitchen can and should reflect your tastes.